Thermal Insulation - External Thermal Insulation Composite System ETICS (Adhesives Plasters -grafiato) List :

Silexcolor Primer
Silexcolor Primer is a modified potassium silicate based primer in water solution.

Silexcolor Base Coat
Transpirant, coloured silicate undercoat with a smooth finish and good filling properties for internal and external surfaces, according to DIN 18363 Standards.Available in the following ulometries: 1.2 mm, 1.8 mm


Silancolor-Base coat
Water-repellent, coloured siloxane undercoat with a smooth finish and good filling properties for internal and external surfaces.

Silancolor-Tonachino
Transpirant, water-repellent, thick-layered siloxane coating product with high filling properties for internal and external surfaces. Available in the following metries: 0.7 mm, 1.2 mm, 1.5

Baumit CreativTop
Ready to use, water repellent, final finishing layer (thin layer) in paste form, for topcoats (finish), inorganic, with stain resistance

Baumit DispersionsKleber
Ready-to-use pasty adhesive for insulation boards

Baumit FillPrimer
Ready to use primer with organic synthetic resins and added fibers, for indoor and outdoor use.

Baumit FillTop
Thin layer mortar, ready for use, in paste form, suitable for applying a smooth surface on Baumit GranoporTop, SilikatTop, SilikonTop with 0.5mm largest grain.

Baumit FineTop
Thin layer mortar, ready for use, in paste form, suitable for creating decorative details. Fine plaster for interior and exterior.

Baumit MosaikTop
Ready to use material with organic binders suitable for final coating thin layer. Water repellent, highly resistant coating with colored pebbles, suitable for internal and external coating particularly at the base.

Baumi NanoporTop
Ready to use, water repellent, final finishing layer (thin layer), in paste form, for topcoats (finish), inorganic, with stain resistance for indoor and outdoor use. Certified according to the specification ETAG 004 and ÖN EN 15824. Thanks to its specially designed microsurface structure, and especially nanocrystalline inorganic additives, soiling of the surface is significantly reduced as the associated algae growth, compared to other coatings.

Baumit openContact
Ready to use mortar for bonding insulation boards open EPS, and for coating of fiberglass.Certified according to ETAG 004 specification For the external thermal insulation system open – Die KlimaFassade.


Baumit SilikonTop
Ready-to-use pasty, silicone resin bound final coat (thin-layer cover coat) with rubbed or grooved structure for interior and outdoor use. Protection and design of facades on old and new mineral plasters andputties, on concrete, for rework on organically bound putties and plasters, as final coat of Baumit ETICS – EPS and mineral as well as on renovation plasters.

Baumit StarContact
Mineral-based, dry powder contact mortar and plaster undercoat for the Baumit External Wall Insulation Systems EPS and XPS. As a thin layer basecoat mortar (with reinforcing mesh) on to Baumit insulation boards and selected render carrier boards. Also suitable for preparing surfaces of coarse render basecoats to receive fine grained (< 2 mm) Baumit decorative topcoats and as a thin bonding coat (keyed) over concrete surfaces to receive further coatings Tested according to ETAG 004.

BAU T50
Fiber¬reinforced cement based adhesive for bonding expanded polystyrene insulation panels in building facades and floors and cementitious substrates. The same material is used for covering of the insulation boards with the application of special fiberglass as an ideal substrate for plaster topcoat. No sliding and increased open application time. The system follows the standard requirements of ETAG 004.


Baumit StellaporTop
Ready for use, finishing layer (thin layer) based on organic polysiloxane resins to form a paste for smooth sanded surface. Suitable for indoor or outdoor use. Part of the external thermal insulation system with EPS, mineral wool, XPS.

Baumit StarTrack
Additional mechanical fixing alternative to standard dowelling for Baumit Open – KlimaFaçade and for Baumit ETICS, in the case of existing old plaster up to a max. total thickness of 40 mm can be bridged over. Drill bit Ø: 8 mm.